Atec Agilent-N9010A Manuale Utente

EXA X-Series Signal Analyzer N9010A10 Hz to 3.6, 7.0, 13.6, 26.5, 32, or 44 GHzData SheetThis data sheet is a summary of the specifications and condit

10Displayed average noise level (DANL) (continued)Preamp on, millimeter-wave (Option 532, 544) 100 kHz to 1 MHz –145 dBm –148 dBm 1 MHz to 1.2 GHz –

11Second harmonic distortion (SHI) Source frequency SHI (nominal)RF/MW(Option 503, 507, 513, 526)10 MHz to 1.8 GHz +45 dBm1.75 to 7.0 GHz +65 dBm7.0 t

12Nominal Range at 1 GHz-130-120-110-100-90-80-70-60-80 -70 -60 -50 -40 -30 -20 -10Mixer Level (dBm)DANL (1 Hz RBW)2nd HarmonicDistortion3rd OrderInte

13Phase noise 1Offset Specification TypicalRF/MW(Option 503, 507, 513, 526)Noise sidebands(20 to 30 °C, CF = 1 GHz)100 Hz –84 dBc/Hz –88 dBc/Hz1 kHz

14Figure 4. Nominal phase noise at different center frequencies for millimeter-wave EXA (Option 532 or 544)Phase noise 1Offset Specification TypicalM

15PowerSuite Measurement SpecificationsChannel powerAmplitude accuracy, W-CDMA or IS95(20 to 30 °C, attenuation = 10 dB)± 0.94 dB (±0.30 dB 95th perce

16General SpecificationsTemperature rangeOperating 0 to 55 °CStorage –40 to 70 °CEMCComplies with European EMC Directive 2004/108/EC•IEC/EN61326-

17Inputs and OutputsFront panelRF input connector Standard (Option 503, 507, 513, or 526) Standard (Option 532 or 544) Type-N female, 50 Ω nominal

18Rear panelNoise source drive +28 V (pulsed) Connector BNC femaleSNS Series noise source connector For use with Agilent SNS Series noise sourcesAna

19I/Q AnalyzerFrequencyFrequency span Standard10 Hz to 10 MHz Option B25 (standard)10 Hz to 25 MHz Option B4010 Hz to 40 MHzResolution bandwidth

2Balance the ChallengesWhether you’re focused on time-to-market, time-to-volume, or costof test, your choice of economyclass signal analyzer should he

20Option B25 (standard) 25 MHz analysis bandwidthIF frequency response (demodulation and FFT response relative to the center frequency, 20 to 30 °C)Ce

www.lxistandard.orgLXI is the LAN-based successor to GPIB, providing faster, more efficient connectivity. Agilent is a founding member of the LXI cons

3Get More InformationThis EXA signal analyzer data sheet is a summary of the specifications and conditions for N9010A EXA and N9010AEP Express EXA sig

4Frequency and Time Specifications Frequency range DC coupled AC coupledOption 503 10 Hz to 3.6 GHz 10 MHz to 3.6 GHzOption 507 10 Hz to 7 GHz 10 MHz

5Sweep time and triggeringRangeSpan = 0 Hz 1 μs to 6000 sSpan ≥ 10 Hz 1 ms to 4000 sAccuracySpan ≥ 10 Hz, swept ± 0.01% nominalSpan ≥ 10 Hz, FFT ± 40%

6Amplitude Accuracy and Range SpecificationsAmplitude range Measurement rangeDisplayed average noise level (DANL) to +23 dBmInput attenuator range(10

7Frequency response Specification 95th percentile (≈ 2σ)(10 dB input attenuation, 20 to 30 °C, preselector centering applied, σ = nominal standard dev

8Input attenuation switching uncertainty Specifications Additional informationAttenuation > 2 dB, preamp off50 MHz (reference frequency) ± 0.20 dB

9Dynamic Range Specifications1 dB gain compression (two-tone)Total power at mixer inputRF/MW(Option 503, 507, 513, 526)20 MHz to 26.5 GHz +9 dBm nomin